Water loss is expected to happen from a swimming pool or a spa at some point when they are in use. Normally, the loss of water from the structure in subject takes place in three main ways, namely, backwashing the filters, evaporation, and splash out. Water loss can be significant to people who stay in arid regions. This is what Queen Creek pool service is all about.
With the abovementioned method of loss of water, it is normal that one should add at least 2 inches of water to the pool/spa each week. However, in case one has to add more than 2 inches each week, it is highly probable that there is a leak. This could be true if there is no other reason for the change in the speed of water loss in the structure.
For instance, it is to be understood that water evaporation may change depending on the season. Also, if the usage of the pool has increased in the recent past, then it may mean that water loss will also increase. However, if none of these has happened yet the loss of water seems to happen at a faster rate, then it may be time to be suspicious.
However, before one goes a step further to call the local pool tech, it is important to confirm the suspicions first. There are a few techniques that one can use to confirm if actually a leak exists in the structure. To detect if a leak exists, one should start by checking the obvious. For instance, one must ensure that the leak is not happening at the equipment pads.
To make sure that the structure does not have a leakage, one should be inspect the filter, pipe valves, pump, and heater. Also, one should check the surrounding ground to make sure it is not wet. One ought to walk around the structure to establish if there is any sunken or eroded surface around the area. If everything is okay, it is then advised to move to the next step of confirmation.
An alternative technique that can be employed to establish whether the structure is leaking is marking the water level inside the structure at the skimmer. This is made possible by use of grease, tape or pencil. Allow the pool a duration of 24 hours prior to coming back to assess the new level of the water.
A normal structure should lose a quarter of an inch per day. If the drop in water level is more than a quarter an inch, then it may be indicative of the existence of a leak. One can also use a bucket filled with water to the same level as the level of water inside the structure. The bucket should then be placed on the steps that are used to access the structure.
The bucket has to be given a duration of 24 hours, after which one should check it. If the level of water in the pool has gone below the height of water in the bucket, then this is confirmation of the presence of a leak. Because the water in both the structure and the bucket are subjected to evaporation, the rate of water loss ought to be the same.
With the abovementioned method of loss of water, it is normal that one should add at least 2 inches of water to the pool/spa each week. However, in case one has to add more than 2 inches each week, it is highly probable that there is a leak. This could be true if there is no other reason for the change in the speed of water loss in the structure.
For instance, it is to be understood that water evaporation may change depending on the season. Also, if the usage of the pool has increased in the recent past, then it may mean that water loss will also increase. However, if none of these has happened yet the loss of water seems to happen at a faster rate, then it may be time to be suspicious.
However, before one goes a step further to call the local pool tech, it is important to confirm the suspicions first. There are a few techniques that one can use to confirm if actually a leak exists in the structure. To detect if a leak exists, one should start by checking the obvious. For instance, one must ensure that the leak is not happening at the equipment pads.
To make sure that the structure does not have a leakage, one should be inspect the filter, pipe valves, pump, and heater. Also, one should check the surrounding ground to make sure it is not wet. One ought to walk around the structure to establish if there is any sunken or eroded surface around the area. If everything is okay, it is then advised to move to the next step of confirmation.
An alternative technique that can be employed to establish whether the structure is leaking is marking the water level inside the structure at the skimmer. This is made possible by use of grease, tape or pencil. Allow the pool a duration of 24 hours prior to coming back to assess the new level of the water.
A normal structure should lose a quarter of an inch per day. If the drop in water level is more than a quarter an inch, then it may be indicative of the existence of a leak. One can also use a bucket filled with water to the same level as the level of water inside the structure. The bucket should then be placed on the steps that are used to access the structure.
The bucket has to be given a duration of 24 hours, after which one should check it. If the level of water in the pool has gone below the height of water in the bucket, then this is confirmation of the presence of a leak. Because the water in both the structure and the bucket are subjected to evaporation, the rate of water loss ought to be the same.
About the Author:
Get excellent tips on how to pick a Queen Creek pool service company and more info about a reliable company at http://www.neptunepoolsaz.com right now.
No comments:
Post a Comment